Fall outfits do not need much to feel seasonal-a pair of tiny crocheted pumpkins can add just the right Halloween touch while staying light enough for comfortable everyday wear.
When autumn events start filling the calendar, it is often the small details that make an outfit feel festive. These cute earrings bring that seasonal touch without needing a large or heavy accessory, making them a nice choice for Halloween gatherings, fall festivals, pumpkin-patch visits, or a simple autumn outfit.
The pumpkin is built in just a few rounds and finished with a little brown stem and green leaf. Once the basic shape is complete, you can leave it as a simple pumpkin or add tiny embroidered facial details for a Jack-o’-lantern expression.
Credit HiruHandmade Crochet
Materials & Tools
- Orange yarn for the pumpkin
- Brown yarn for the stem
- Green yarn for the leaf
- 2.5 mm crochet hook
- Yarn needle
- Pair of earring hooks
- Jewelry pliers
- Scissors
Finished Size
Each pumpkin earring is approximately 1 inch (2.5 cm) in diameter when made with the specified yarn and 2.5 mm crochet hook.
Since you are making a pair, try to keep your tension consistent so both pumpkins finish at a similar size.
Pattern Abbreviations
- ch: chain
- sc: single crochet
- hdc: half double crochet
- dc: double crochet
- sl st: slip stitch
- st: stitch
- inc: increase – work 2 stitches into the same stitch
- yo: yarn over
- MR: magic ring
This pattern uses US crochet terminology.
Steps: Crochet the Pumpkin
The pumpkin begins in the center and grows outward. The increases in the first few rounds create the rounded base, while the later combination of stitches gives the edge a more pumpkin-like shape.
Round 1: Make an MR, work 6 sc into the ring, pull the yarn tail to close the center, then join with a sl st into the first sc. (6 sts)
Keep the center snug after closing the magic ring, but do not pull it so tightly that the stitches become difficult to see or work into.
Round 2: Ch 1, work 1 inc in each stitch around, then join with a sl st into the first sc. (12 sts)
Round 3: Ch 1, repeat [1 sc, 1 inc] around, then join with a sl st into the first sc. (18 sts)
The circle should now be noticeably wider. If it looks uneven, gently flatten it with your fingers before moving on rather than trying to correct the shape by pulling the yarn.
Round 4: Ch 1, work 1 sc in the first stitch, 1 hdc inc in the next stitch, then 1 hdc in each of the next 2 stitches; repeat the hdc increase and 2 hdc sequence around, then join with a sl st into the first sc. (24 sts)
The taller hdc stitches begin to give the pumpkin more visual height and help distinguish it from a plain crochet circle.
Round 5: Ch 1, work 1 sc in each of the first 2 stitches, 1 hdc inc in the next stitch, 2 hdc inc in the next 2 stitches, then 1 hdc in the next stitch; work 1 sl st in each of the next 4 stitches, then continue the increase and slip-stitch sequence according to the tutorial until the end of the round; finish with 1 sc in each of the final 2 stitches and join with a sl st to the starting sc.
Cut the orange yarn and leave a long tail for sewing.
This round moves between several stitch types, so it is worth following the sequence slowly. The slip stitches sit lower along the edge while the increases create the fuller sections of the pumpkin.
Add the Brown Stem
The stem is crocheted directly onto the pumpkin, so there is no separate stem piece to position and sew on later.
Stem
Stem: Switch to brown yarn and insert the hook into a stitch just before the final joining point of the pumpkin; pull up a loop, ch 4, skip the first chain, work 2 sc in the second chain from the hook, then 1 sc in each of the next 2 chains; insert the hook into the base joining point and make a sl st.
Fasten off and leave a tail for securing.
Before trimming the yarn, check that the stem is sitting upright from the top of the pumpkin. If it is loose at the base, secure that connection rather than simply adding length to the stem.
Add the Green Leaf
The leaf is worked directly beside the stem.
Leaf: Switch to green yarn and insert the hook into a stitch just after the final joining point of the pumpkin; pull up a loop, ch 7, then work sl st in the second chain from the hook, sc in the next chain, hdc in the next chain, dc in the next chain, hdc in the next chain, and sc in the final chain; insert the hook back into the base stitch and make a sl st.
Cut the yarn, leaving a tail, and weave the ends securely into the back.
Once the leaf is attached, gently position it beside the stem. Avoid pulling it tightly against the pumpkin because leaving it slightly open helps the leaf remain visible when the earring is hanging.
Add a Jack-o’-Lantern Face
The face is optional, so the earrings can remain simple if you prefer the clean pumpkin shape.
For a Jack-o’-lantern version, use black embroidery thread to stitch two small eyes and a simple smile onto each pumpkin.
Because the pumpkin is only about an inch wide, keep the facial features small. Place the eyes first and check their spacing before adding the smile so the expression stays centered.
Attach the Earring Hook
Before attaching the hardware, decide which side of the pumpkin should face outward.
Use jewelry pliers to open the small ring on the earring hook. Thread the open ring through a stitch near the top of the pumpkin, close to the stem, and then close the ring firmly with the pliers.
Repeat with the second pumpkin.
Before finishing the second attachment, compare the two earrings side by side. The hooks should face the same direction so the pumpkins hang consistently when worn.
Final Check
Check that both earring hooks are completely closed and that the stem and leaf are secure.
Give each earring a gentle pull at the attachment point. If nothing shifts and the pumpkin hangs naturally, the pair is ready to wear.
The finished earrings add a small seasonal detail without overwhelming an outfit, making them especially easy to pair with other fall or Halloween accessories.
